USB Type-C

ANX7451

Re-timers/Repeaters
USB-C
10G Active Mux (4x4) with Integrated Re-timers for U5B3.2/DisplayPortTM
Overview: 

ANX7451 is a 4x4 re-timing mux capable of switching DisplayPort (DP) and USB3.2 Gen 2 10Gbps signals to support a single USB Type-C™ (USB-C™) port. ANX7451 has built-in re-timers to recover both the USB and DP signals with loss compensation of 23dB for USB and up to 27dB for DP. ANX7451 supports Separate Reference Clock Independent SSC (SRIS) and Bit-Level Re-timer (BLR) architectures for a hybrid implementation for Gen 1 and Gen 2. SRIS re-timers eliminate jitter transfer and guarantee Gen 2 high-speed operation. Host (source) and device (sink) applications are fully supported by ANX7451 with built-in intelligent switching. With the intelligent digital switching, ANX7451 ensures the enhanced signals from the retimers are preserved and outputted over the USB-C connector. ANX7451 integrates the local reference clock and SBU/AUX mux for switching DP AUX signals and reducing overall system BOM cost.

Main Features: 
Other Features
  • Built-in re-timers 
    • Integrated re-timers for USB3.2 up to Gen 2 @ 10Gbps
    • US3.2 Specification (Appendix-E) compliant re-timer
    • Supports both Separate Reference Clock Independent SSC (SRIS) and Bit-Level Re-timer (BLR) Architectures of USB3.2 Specification (Appendix-E)
    • Integrated re-timers (Link training-tunable PHY repeater) for DisplayPort up to HBR3 @ 8.1Gbps. Supports both transparent mode and non-transparent mode (transparent or LTTPR)
    • Supports both host (source) and device (sink) applications in USB-C subsystems
    • Loss compensation to recover up to 23dB channel loss (USB), up to 27dB (DP)
  • Integrated mux
    • Integrated (4x4) mux switches USB and DP signals and preserves enhanced signal output over USB-C connector
    • Mux control input through I2C commands from external I2C master (or, optionally through GPIO of FLIP/USB_EN/DP_EN pins)
    • Integrated SBU/AUX mux for switching DisplayPort AUX +/- signals
  • Integrated reference clock
  • Serial and debug interfaces
    • I2C Slave interface, up to 1MHz, for mux and re-timer configuration
  • Industry standard compatibility
    • USB3.2 specification, Appendix E
    • DisplayPort 1.4a specification
    • USB Type-C r1.2 specification
    • Intel USB3.2 Repeater and Active Switch specification
  • Low-power design
    • Analog power supply at 1.8V
    • I/O power supply at 1.8V
    • Core power supply at 1.2V
  • Package
    • QFN-50, 4.7mm x 6.4mm, 0.90mm Z-height, 0.35mm pin-pitch
    • LGA-34, 3.3mm x 4.8mm, 0.71mm Z-height, 0.35mm pin-pitch
  • Commercial temperature range of OC to 70C 
Applications: 

Accessories

Notebook/Desktop PC

Storage/Server

Package: 

QFN-50, 4.7mm x 6.4mm, 0.90mm Z-height, 0.35mm pin-pitch

LGA-34, 3.3mm x 4.8mm, 0.71mm Z-height, 0.35mm pin-pitch

Detailed Product Information: 

2ch

ANX7412

USB-C Port Controller
USB-C
USB-C™ Port Controller
Overview: 

ANX7412 is a USB Type-C™ (USB-C) Port Controller that complies with the latest USB-C (r1.2) and USB-PD v3.0 (r1.0) specifications. ANX7412 integrates the logic to manage cable attach and detach, orientation, and role detection. The onchip microcontroller (OCM) facilitates USB-PD v3.0 messaging for fast charging, DisplayPort™ (DP) Alternate Mode (Alt Mode), and Vendor-Defined Messages (VDMs). ANX7412 integrates the MOSFETs for powering VCONN and the signals required to control external VBUS load switches. ANX7412 can be configured as a Downstream Facing Port (DFP) or a Dual- Role Port (DRP), making it an ideal solution for USB-C receiver ports such as dongles, docks, HDTV, monitors, and projectors. ANX7412 supports a TCPC-compliant register interface and utilizes its I2C Slave port for communication with an upstream embedded controller, CPU, or AP. ANX7412 is powered from a single flexible supply rail at 3.3V and is available in small QFN packages.

Main Features: 
Other Features
  • TCPC-compliant hardware interface
  • Supports DFP and DRP modes for Host-only or Dual-Role applications
  • Integrated VCONN FETs
  • Built-in 10-bit ADC to monitor VBUS voltage and current
  • Integrated Billboard
  • Dedicated control signals for VBUS Source FET, VBUS sink FET, and VBUS auto discharge circuity
  • Serial and debug interfaces
    • I2C Master/Slave interface
  • Industry standard compatibility
    • USB Type-C r1.2 specification
    • USB Power Delivery v3.0 r1.0 specification
    • DisplayPort 1.4 specification
    • DisplayPort Alternate Mode over USB Type-C r1.1 specification
    • Universal Serial Bus (USB) Type-C Port Controller Interface r1.0 specification
  • Low-power design
    • Single supply at 3.3V
    • Dedicated supply power pin for flexible I/O power — 1.8V or 3.3V
    • Ultra-low power consumption (typical 77uW) in standby mode
  • On-chip microcontroller with reprogrammable memory for USB-PD v3.0 engine
    • 64K bytes SRAM for firmware execution
    • 128K bytes Flash for firmware storage
    • PDFU function for firmware updating
  • Dead battery detection support
  • Package
    • QFN-28, 4mm x 4mm, 0.8mm Z-height, 0.4mm pin-pitch
Applications: 

Accessories

Notebook/Desktop PC

Smartphone/Tablet

Package: 
  • QFN-28, 4mm x 4mm, 0.8mm Z-height, 0.4mm pin-pitch
Detailed Product Information: 

ANX7411

USB-C Port Controller
USB-C
USB-C'" Port Controller
Overview: 

ANX7411 is a USB Type-C’" (USB-C) Port Controller that complies with the latest USB-C (r1.2) and USB-PD v3.0 (r1.0) specifications. ANX7411 integrates the logic to manage cable attach and detach, orientation, and role detection. The on- chip microcontroller (OCM) facilitates USB-PD v3.0 messaging for fast charging, DisplayPort" (DP) Alternate Mode (Alt Mode), and Vendor-Defined Messages (VDMs). ANX7411 integrates the MOSFETs for powering VCONN and the signals required to control external VBUS load switches. ANX7411 can be configured as a Downstream Facing Port (DFP) or a Dual- Role Port (DRP), making it an ideal solution for various applications such as notebooks, desktops, and 2-in-1 PCs. ANX7411 supports a TCPC-compliant register interface and utilizes its I2C Slave port for communication with an upstream embedded controller, CPU, or AP. ANX7411 is powered from a single flexible supply rail at 3.3V and is available in small QFN packages.

Main Features: 
Other key features
  • TCPC-compliant hardware interface
  • Supports DFP and DRP modes for Host-only or Dual-Role applications
  • Integrated VCONN FETs
  • Built-in 10-bit ADC to monitor VBUS voltage and current
  • AUX CH/SBU Mux
  • Dedicated control signals for VBUS Source FET, VBUS sink FET, and VBUS auto discharge circuity
  • Serial and debug interfaces
    • I2C Master/Slave interface
  • Industry standard compatibility
    • USB Type-C r1.2 specification
    • USB Power Delivery v3.0 r1.0 specification
    • DisplayPort 1.4 specification
    • DisplayPort Alternate Mode over USB Type-C r1.1 specification
    • Universal Serial Bus (USB) Type-C Port Controller Interface r1.0 specification
  • Low-power design
    • Single supply at 3.3V
    • Dedicated supply power pin for flexible I/O power — 1.8V or 3.3V
    • Ultra-low power consumption (typical 77uW) in standby mode
  • On-chip microcontroller with reprogrammable memory for USB-PD v3.0 engine
    • 64K bytes SRAM for firmware execution
    • 128K bytes Flash for firmware storage
    • PDFU function for firmware updating
  • Dead battery detection support
  • Package
    • QFN-28, 4mm x 4mm, 0.8mm Z-height, 0.4mm pin-pitch
Applications: 

Accessories

Notebook/Desktop PC

Smartphone/Tablet

Package: 
  • QFN-28, 4mm x 4mm, 0.8mm Z-height, 0.4mm pin-pitch
Detailed Product Information: 

ANX7402

USB-C Port Controller
USB-C
USB Power Delivery PHY with Channel Configuration Control
Overview: 

ANX7402 is a USB Power Delivery (USB-PD) PHY with an On-chip Microcontroller (OCM). The OCM enables ANX7402 to manage the cable detection, USB Power Delivery negotiations, Vendor Defined Message (VDM) communication protocol, and other functions, as defined in the USB Type-C™ v1.1 and USB Power Delivery v2.0 specifications. ANX7402 supports a Hot Plug Detect (HPD) input pin and converts the HPD signal over the Configuration Channel (CC) to enable DisplayPort™ (DP) Alt Mode applications. When paired with a DP-to-HDMI/VGA bridge (such as the ANX7737/9837) and a USB Billboard device IC, the ANX7402 creates an ideal solution for USB Type-C (USB-C™) dongle and docking station applications.

Main Features: 
  •  On-chip Microcontroller (OCM) to implement cable detection and USB-PD messaging for charging related functions
  •  5V-tolerant CC/VCONN signals
  •  Dead battery charging support
  •  I2C slave mode to support external MCU/IC
  •  VBUS control and USB_ID pins to control external switch, Power Management Integrated Circuits (PMICs) or USB charger IC based on    the USB-PD configuration 
  •  3.3V power supply (1.0V Core power generated by internal regulator)
  •  Supports the following
    •  USB Power Delivery Specification v2.0 on CC wire
    •  HPD input pin and conversion over CC for DP Alt Mode applications
  •  Designed to the following specifications 
    •  USB Type-C Cable and Connector Specification  v1.1
    •  USB Power Delivery Specification v2.0
Applications: 

Accessories

Notebook/Desktop PC

Smartphone/Tablet

Standards Compliance: 

USB Power Delivery Specification v2.0 (rev 1.0)

USB Type-C Cable and Connector Specification (rev 1.0)

Detailed Product Information: