10G Active Redriver with Linear Equalization for USB3.2/DisplayPort™
Overview:
ANX7493-AA is a 4-lane redriver capable of switching DisplayPort (DP) and USB3.2 Gen 2x2 10Gbps signals to support a single Type-C™ (USB-C™) port with DisplayPort Alternate Mode. ANX7493-AA can be also configured to a DisplayPort (DP)2.0 Redriver which supports up to 4-lane UHBR10. It is backward compatible with DP 1.4a and USB3.2 Gen 2x2 and Gen 2x1 protocols. Each lane in the ANX7493-AA Redriver has a maximum signal speed of 10Gbps. Two lanes can be bonded to increase the total link bandwidth to 20Gbps. Work modes are set via I2C registers. ANX7493-AA has built-in redriver to recover both the USB and DP signals with loss compensation of 12dB for USB and DP. ANX7493-AA supports a high-gain bandwidth linear amplifier with Continuous Time Linear Equalization (CTLE). ANX7493-AA integrates the AUX snooping for detecting DP states.
Main Features:
Built-in redrivers
Integrated re-driver for USB3.2 up to Gen 2 @ 10Gbps
Integrated re-drivers for DisplayPort up to UHBR10 @ 10Gbps.
Supports both host (source) and device (sink) applications in USB-C subsystems with DisplayPort Alternate Mode
Loss compensation to recover up to 12dB channel loss
Work mode and CTLE configurations
Work mode set by I2C registers
Datapath orientation and direction set by I2C registers or GPIO
CTLE configurations set by I2C registers or GPIO
Serial and debug interfaces
I2C Slave interface, up to 1MHz, for mux and redriver configuration
Industry standard compatibility
USB3.2 specification
DisplayPort 2.0 specification
USB Type-C r2.0 specification
Low-power design
AUX CH commands snooping for power saving in DP mode
USB high speed and LFPS signals detection for power saving in USB mode
Analog power supply at 1.8V
I/O power supply at 1.8V − Integrated Core power supply at 1.2V
Commercial temperature range of 0C to 70C
Applications:
Accessories
Notebook/Desktop PC
Storage/Server
Package:
QFN-50, 4.7mm x 6.4mm, 0.90mm Z-height, 0.35mm pin-pitch
RD1011 is a bidirectional active USB Type-CTM (USB-C) cable, which includes two paddle cards, each with an ANX7451 device on it. The ANX7451 is a 4x4 re-timing mux capable of switching DisplayPort (DP) and USB3.2 Gen 2 10Gbps signals to support a single USB Type-CTM (USB-CTM) port. The RD1011 design can recover both the USB and DP signals with loss compensation of up to 23dB and 27dB respectively. The RD1011 includes two ANX7410 devices, which act as an on-board programmable MCU and eMarker chip. With ANX7410, ANX7451 can be initiated with optimal settings that enable the RD1011 design to cover 4-meter at 28AWG cable length. RD1011 can be used with any USB-C port on any of the display monitors, docking stations and VR HMDs.
Main Features:
Other Features
Bidirectional active USB-C cable carrying 4L DP or 2L DP and USB3.2
Supports up to 4L of DisplayPort in/out, with signal conditioning up to 8.1Gbps (supports HBR3, HBR2, HBR, RBR rates)
Supports USB3.1 in/out, with signal conditioning up to 10Gbps
Supports USB2.0 (480Mbps)
Compensates signal loss of up to 27dB
Supports plug flip
Powered by VCONN and VBUS
On-board programmable MCU, ANX7410, to initiate ANX7451 with specific settings
ANX7410 acts as an eMarker chip to snoop or respond SOP’ and SOP’’ messages from a USB-C DFP, as per active USB-C cable spec
Two paddle cards (2x re-timers) design to guarantee data throughput performance, and for ease of production
ANX6210 is a DisplayPort to VGA converter designed for motherboards. With its single HRB2 lane, ANX6210 can support WDXGA (2048x1152) as its max resolution. Its on-chip MCU and memory eliminates the needs for any external configuration or setup. It automatically directs the DisplayPort output from the PC or mobile phone to VGA, effectively working with all types of legacy monitors, projectors, and TVs. ANX6210 supports a single 3.3V power supply with an integrated 1V low-dropout (LDO) regulator.
Main Features:
VGA Output
Supports resolutions up to WDXGA (2048x1152@60Hz,24bpp)
VGA output meets VESA VSIS v1r2 clock jitter specification
VGA DAC work range is up to 270 MHz
Low power standby mode with automatic monitor plug and unplug detect
Powered from DisplayPort source
EDID and MCCS pass-through support
DisplayPort Input
DisplayPort 1.2 compliant receiver
VESA® compliant eDP v1.3 receiver
1 lane high-speed differential input with configurable speed: 5.4Gbps, 2.7Gbps, or 1.62Gbps
Optimized for motherboard design
With 1.0 LDO on, single 3.3V power supply supported
Super low power consumption: 480mW active power (1080p@60Hz, 1V LDO powered on)
While VGA is losing its popularity in notebooks, there continues to be a need for VGA connections with its huge installed base of monitors, projectors, and TVs. The ANX6212, designed for motherboards, addresses this gap through the high performance DisplayPort to VGA converter of its kind. With its on-chip MCU and memory, the ANX6212 does not require any external configuration or setup. The ANX6212 automatically directs the DisplayPort output from the PC or mobile phone to VGA, effectively working with all types of legacy monitors, projectors, and TVs.
Main Features:
VGA Output
Supports resolutions up to WQXGA (2560x1600@60Hz, 24bpp)
VGA output conforms to VESA® VSIS v1r2 clock jitter specification
VGA output pixel rate up to 270 MHz
Low power standby mode with automatic monitor plug and unplug detect
EDID and MCCS pass-through support
DisplayPort Input
VESA compliant DisplayPort 1.2 receiver
VESA compliant eDP v1.3 receiver
Two-lane high-speed differential input with configurable speed: 5.4Gbps, 2.7Gbps, or 1.62Gbps
Optimized for VGA Adapters
Integrated MCU and EEPROM for added flexibility
Single 3.3V power supply
5.0V power output for VGA DDC
Minimum BOM requirements
System Operation
Under 350mW operation at WUXGA resolutions (no regulators)
Field upgradable through DP AUX or I2C
MCU can control external components
-10 to +75o C operating temperature
Applications:
Automotive
Notebook/Desktop PC
Package:
6x6mm, 48 QFN (0.4mm pitch)
Standards Compliance:
DisplayPort 1.2
eDP 1.3
Power Requirements:
600mW active power with all regulators active
Standby Power: 12mW with 1V low-dropout (LDO) regulator off
The ANX6211 is a DisplayPort to VGA converter featuring low power consumption, high performance, and cost-effective. Designed for motherboards, the ANX6211 is optimized in terms of space, power, and performance for the next generation of CPUs. Analogix’s expertise in DisplayPort to VGA design ensures compatibility with all existing VGA displays.
Main Features:
VGA Output
Supports resolutions up to WQXGA (2560x1600 @60Hz, 24bpp)
VGA output meets VESA VSIS v1r2 clock jitter specification
VGA output pixel rate up to 270 MHz
Low power standby mode with automatic monitor plug and unplug detect
EDID and MCCS pass-through support
DDC speed control for use with longer VGA cables
DisplayPort Input
VESA compliant DisplayPort 1.2 receiver
VESA compliant eDP v1.3 receiver
2 lane high speed differential input with configurable speed: 5.4Gbps, 2.7Gbps, or 1.62Gbps
Power optimized for Ultra books
Under 350mW operation at WUXGA resolutions
15mW standby power
DisplayPort HBR2 capability allows for single lane operation up to WUXGA. Saves 50mW of DP Tx power
3.3V and 1.05V power requirements easily found on next generation motherboards. No need for external regulators, saving power, space, and cost.
Other Features
Minimum BOM requirements
Default settings changeable with I2C
-10 to +75o C operating temperature
Applications:
Automotive
Notebook/Desktop PC
Package:
7x7mm, 48 QFN (0.5mm pitch) package
Standards Compliance:
DisplayPort 1.2
eDP 1.3
Power Requirements:
3.3V and 1.05V power requirements easily found on next generation motherboards.
ANX1122 is a high-performance low power DisplayPort 1.2 to 24bpp dual-/single-channel LVDS translator. It is designed for connecting motherboards to legacy LVDS LCD panels.
Main Features:
DisplayPort Input Interface
eDP 1.3 compliant
1/2 lane high-speed differential input with configurable speed: 5.4Gbps, 2.7Gbps, or 1.62Gbps
Resolutions up to WQXGA (2560x1600@60Hz, 24bpp) with pixel clock frequency up to 270 MHz
Industrial temperature version only supports 2.7 and 1.62Gbps DisplayPort connections (resolutions up to WUXGA, 1920x1200)
Standard AUX channel link up to 1Mbps bandwidth
DisplayPort mode spread spectrum clock (SSC) support
Stereo (3D) video output support
LVDS Output Interface
8-BPC LVDS output with single/dual ports
Programmable LVDS swing, channel swap, and polarity invert
LVDS central spectrum spreading with amplitude up to +/-1.75%
Programmable by the DP transmitter through AUX channel, or by local I2C slave
ANX1121 is a low cost high quality DisplayPort to LVDS converter offering up to 18-bits per pixel and single channel LVDS output support. It provides a bridge between DisplayPort-enabled next generation source devices (such as GPUs) and existing LVDS displays. Featuring low power and EMI reduction techniques, combined with its low cost and small form factor, it is ideal for motherboards and other systems with embedded displays.
Main Features:
VESA Compliant DisplayPort™ 1.1a Receiver
Configurable 1 lane operation
1.62/2.7Gbps data rate support
AUX channel link up to 1Mbps bandwidth
All DisplayPort receiver side registers accessible by the AUX channel and I2C slave interface
Spread spectrum clock (SSC) support for improved EMI performance
Single channel LVDS output
Single Channel: Up to 120 MHz pixel clock
Up to 18-bits per pixel
Video Modes
Up to 1680 x 1050@60Hz
18 bits per pixel support
LVDS Spread Spectrum Clocking for reduced EMI
On-chip ring oscillator, no external clock required
Low BOM cost, no local MCU required
Fully controllable via DisplayPort Tx through AUX channel
Low power design supporting several power saving modes
The ANX7738 is a SlimPort to HDMI (up to Ultra-HD, 4K in Turbo mode) converter, which includes 3D display delivery capability.Also, it is designed to interoperate with any other MyDP or DisplayPort™ enabled transmitter,with a maximum resolution of Full-HD including 3D display, in ultrathin notebooks, tablets, smartphones, camcorders, and digital still cameras. ANX7738works in conjunction with MyDP/DisplayPort transmitters, such as the ANX7812, ANX7814, ANX7816, and more. ANX7738 transforms the MyDP/DisplayPort or SlimPort (Turbo mode) output of a source device to HDMI or DVI output so that the device can connect to any high-definition TV, monitor, or projector.
Main Features:
HDMI Transmitter
Connects to any HDMI receiver
Max TMDS link rate up to 300Mpixels/sec
Up to 36bpp color depth support at Full-HD
3D video output support
Remote control support through Consumer Electronics Control (CEC)
HDCP content protection
SlimPort/MyDP/DisplayPort Receiver
SlimPort (Turbo mode) DisplayPort or MyDP input
Configurable 1-lane input supports: Turbo mode, HBR2, HBR, and RBR data rates
Advanced WideEye™ SerDes technology capable of receiving data over long and low quality cables
Spread Spectrum Clocking (SSC) support
Stereo (3D) video input support
Single wire AUXP (C-WIRE) sideband communication
Integrated remote control support
HDCP content protection
System Operation
Integrated On-chip Microcontroller (OCM) for software free operation
Slave I2Cdevice control interface
Built-in video test pattern generator
Applications:
Accessories
Notebook/Desktop PC
Smartphone/Tablet
Package:
64-pin QFN, 8mm x 8mm, 0.4mm pin-pitch
Standards Compliance:
MyDP
RoHS Compliant and Halogen Free
HDMI
HDCP
DisplayPort
Power Requirements:
1.0V and 1.8V
3.3V input requirement eliminated by an integrated boost regulator
Standby power: <20mW, while monitoring cable detection
.png)
