USB 3.1 Gen2

ANX7437

Switches/Multiplexers
USB-C
USB Type-C™ Crosspoint Switch with On-chip Microcontroller
Overview: 

ANX7437 is an intelligent crosspoint switch that supports switching at data rates of up to 10Gbps. ANX7437 supports highspeed interfaces, such as USB 3.1 (Gen 1 – 5Gbps, Gen 2 – 10Gbps). ANX7437 is designed as a companion IC to various CPUs and Application Processors (APs) to enable notebooks, desktops, and 2-in-1 PCs to use the reversible USB Type-C (USB-C™) connectors. An On-chip Microcontroller (OCM) is available to manage the signal switching, Channel Configuration (CC) detection, USB Power Delivery (USB-PD) charging and Vendor Defined Message (VDM) protocol, and other functions, as defined in the USB Type-C v1.2 and USB Power Delivery v3.0 specifications. ANX7437 can be configured for a Downstream Facing Port (DFP) or Dual-Role Port (DRP) to support a USB-C receptacle.

Main Features: 
Other Features
  • USB 3.1 signal (SSTX and SSRX) with Gen1 (5Gbps) and Gen2 (10Gbps) link speed
  • Native TCPC-compliant hardware register interface
  • Supports DFP and DRP modes for Host-only or Dual-Role applications
  • Integrated VCONN FETs
  • Built-in 10-bit ADC to monitor VBUS voltage and current
  • Dedicated control signals for VBUS Source FET, VBUS sink FET, and VBUS auto discharge circuity
  • Serial and debug interfaces
    • Slave interface
    • Direct Connect Interface (DCI) debug support
  • Industry standard compatibility
    • USB Type-C r1.2 specification
    • USB Power Delivery v3.0 r1.0 specification
    • Universal Serial Bus (USB) Type-C Port Controller Interface r1.0 specification
  • Low-power design
    • Single supply at 3.3V
    • Dedicated supply power pin for flexible I/O power – 1.8V or 3.3V
    • Ultra-low power consumption (typical 80uW) in standby mode
  • On-chip Microcontroller (OCM) to implement signal switching and USB-PD messaging
    • 64K bytes SRAM for firmware execution
    • 128K bytes Flash for firmware storage
    • PDFU function for firmware updating
  • Package offered: 48-pin QFN, 6mm x 6mm, 0.8mm Z-height, pin-pitch: 0.4mm
Applications: 

Accessories

Notebook/Desktop PC

Package: 
  • 48-pin QFN, 6mm x 6mm, 0.8mm Z-height, pin-pitch: 0.4mm
Detailed Product Information: 

2L

ANX7490

Re-timers/Repeaters
USB-C
10G USB 3.1 Re-timer (1-Port)
Overview: 

ANX7490 is a USB 3.1 1-port re-timer capable of conditioning USB signals at both Gen 1 (5Gbps) and Gen 2 (10Gbps) speeds. ANX7490 can compensate signal loss of up to -23dB and is compliant to the latest USB 3.1 specifications. ANX7490 is protocol aware for better link power management and power savings. ANX7490 can be in various types of applications such as notebook/desktop PCs, server, and accessories/docks with various USB connectors such as Type-A, Type-B, or even USB Type-CTM (USB-CTM).

Main Features: 
Other key features
  • Built-in re-timers
    • Integrated re-timer for USB 3.1 1-port (Tx/Rx) up to 10Gbps
    • Loss compensation to recover up to 23dB channel loss
  • Protocol awareness for better link power management (LPM) and savings
  • Reference clock for re-timers
    • Utilizes a 24MHz reference XTAL or 1.05V single-ended clock source
  • Serial and debug interfaces
    • I2C Slave interface, up to 1MHz, for re-timer configuration
    • DCI debug interface support
  • Industry standard compatibility
    • USB 3.1 specification, Appendix E
    • Intel USB 3.1 Repeater and Active Switch specification
  • Low-power design
    • Analog power supply at 1.8V
    • Dedicated supply power pin for I/O power at 1.8V
  • Package
    • BGA-42, 3.5mm x 4.0mm, 0.5mm ball-pitch
    • QFN-40, 5mm x 5 mm, 0.4mm pin-pitch
  • Industrial temperature range of -40C to 85C
  • Applications
    • Notebooks, desktops, server and accessories/docks
Applications: 

Accessories

Notebook/Desktop PC

Package: 
  • BGA-42, 3.5mm x 4.0mm, 0.5mm ball-pitch
  • QFN-40, 5mm x 5 mm, 0.4mm pin-pitch
Detailed Product Information: 

2L

ANX7430

Re-timers/Repeaters
USB-C
10G Active Mux (1x2) with Integrated Re-timer for U SB 3.1
Overview: 


ANX7430 is a USB 3.1 Gen 2 10G active mux with integrated re-timer capable of recovering the USB signals with loss compensation of up to 23dB. ANX7430 also integrates a mux (1x2) for USB Type-C™ (USB-C™) applications. Digital muxing is supported by ANX7430 to ensure the enhanced signals from the re-timer are preserved and outputted over the USB-C connector.
 

Main Features: 
Other key features
  • Built-in re-timers
    • Integrated re-timers for USB 3.1 up to Gen 2 @ 10Gbps
    • Loss compensation to recover up to 23dB channel loss
  • Integrated mux
    • Digital (1x2) mux switches USB signals and preserves enhanced signal output over USB-C connector
    • Mux control input through I2C commands from external I2C master (or, optionally through FLIP/OP_MODE pins)
  • Reference clock for re-timers
    • Utilizes a 24MHz crystal or 1.05V swing single-ended clock source
  • Serial and debug interfaces
    • I2C Slave interface, up to 1MHz, for mux and re-timer configuration
    • DCI debug interface support
  • Industry standard compatibility
    • USB 3.1 specification, Appendix E
    • USB Type-C r1.2 specification
    • Intel USB 3.1 Repeater and Active Switch specification
  • Low-power design
    • Analog power supply at 1.8V
    • Dedicated 3.3V power for DCI interface
    • Dedicated supply power pin for I/O power at 1.8V
  • Packages
    • BGA-42, 3.5mm x 4.0mm, 0.5mm ball-pitch
    • QFN-48, 6mm x 6mm, 0.85mm Z-height, 0.4mm pin-pitch
    • QFN-60, 7mm x 7mm, 0.85mm Z-height, 0.4mm pin-pitch
  • Industrial temperature range of -40C to 85C
Applications: 

Accessories

Notebook/Desktop PC

Storage/Server

Package: 
  • BGA-42, 3.5mm x 4.0mm, 0.5mm ball-pitch
  • QFN-48, 6mm x 6mm, 0.85mm Z-height, 0.4mm pin-pitch
  • QFN-60, 7mm x 7mm, 0.85mm Z-height, 0.4mm pin-pitch
Detailed Product Information: 

2L

ANX7440

Re-timers/Repeaters
USB-C
10G Active Mux (6x4) with Integrated Re-timers for USB™ 3.1/DisplayPort™
Overview: 

ANX7440 is a re-timing mux capable of switching DisplayPort (DP) and USB 3.1 Gen 2 10Gbps signals to support a single USB Type-C™ (USB-C™) port. ANX7440 has built-in re-timers to recover both the USB and DP signals with loss compensation of up to 27dB. Digital muxing (6x4) is supported by ANX7440 to ensure the enhanced signals from the re-timers are preserved and outputted over the USB-C connector. ANX7440 integrates the SBU/AUX mux for switching DP AUX signals and reducing overall system BOM cost.

Main Features: 
Other key features
  • Built-in re-timers
    • Integrated re-timers for USB 3.1 up to Gen 2 @ 10Gbps
    • Integrated re-timers (Link training-tunable PHY repeater) for DisplayPort up to HBR3 @ 8.1Gbps. Supports both transparent mode and non-transparent mode (transparent or LTTPR).
    • Loss compensation to recover up to 23dB channel loss (USB), up to 27dB (DP)
  • Integrated mux
    • Integrated (6x4) mux switches USB and DP signals and preserves enhanced signal output over USB-C connector
    • Mux control input through I2C commands from external I2C master (or, optionally through FLIP/OP_MODE pins)
    • Integrated SBU/AUX mux for switching DisplayPort AUX +/- signals
  • Reference clock for re-timers
    • Utilizes a 24MHz crystal or 1.05V swing single-ended clock source
  • Serial and debug interfaces
    • I2C Slave interface, up to 1MHz, for mux and re-timer configuration
    • DCI debug interface support
  • Industry standard compatibility
    • USB 3.1 specification, Appendix E
    • DisplayPort 1.4 specification
    • USB Type-C r1.2 specification
    • Intel USB 3.1 Repeater and Active Switch specification
  • Low-power design
    • Analog power supply at 1.8V
    • Dedicated 3.3V power for PULL_1 and PULL_2, DCI interface
    • Dedicated supply power pin for I/O power at 1.8V
  • Commercial temperature range of 0C to 70C

Applications: 

Accessories

Display/Panel

Notebook/Desktop PC

Smartphone/Tablet

Notebooks, desktops, and 2-in-1s
Package: 
  • BGA-56, 4.0mm x 4.5mm, 0.8mm Z-height, 0.5mm ball-pitch
  • QFN-60, 7.0mm x 7.0mm, 0.85mm Z-height, 0.4mm pin-pitch
Power Requirements: 
  • Low-power design
    • Analog power supply at 1.8V
    • Dedicated 3.3V power for PULL_1 and PULL_2, DCI interface
    • Dedicated supply power pin for I/O power at 1.8V 
Detailed Product Information: